咨询热线: 15269186692
酒店家具定制实用的实木拼板的方法
来源:https://www.jnzxjjpf.com/ 时间:2021-12-21 浏览量:
现代酒店家具定制为了更加方便高效、性价比等原因,大面积板材使用都会用到拼板,主要是因为餐桌、床板、衣柜面、门等这些面积相对比较大的,如果用整块板材制作成本是很高的,也是不实际的。而大多数情况下我们看到的都是拼接板做的。
Modern hotel furniture customization in order to be more convenient, efficient, cost-effective and other reasons, panel will be used in the use of large-area panels, mainly because the areas of dining table, bed board, wardrobe surface and door are relatively large. If the whole panel is used, the cost is very high and impractical. In most cases, what we see is made of splice plates.
酒店家具定制实木拼接板是采用不同的结构形式,将实木窄板拼合成所需宽度的板材,不同的拼接法带来不同的观赏效果。
The customized solid wood splicing board of hotel furniture adopts different structural forms to splice the narrow solid wood board into the board with the required width. Different splicing methods bring different viewing effects.
实木拼板的常规厚度:桌面、屉面板为16-25mm,厚桌面30-50mm,嵌板6-12mm,屉旁板、屉背板10-15mm。为了尽量减少拼板的收缩和翘曲,实木窄板的宽度应有所限制,在现代家具生产中,一般实木窄板不超过60mm。
Conventional thickness of solid wood panel: 16-25mm for desktop and drawer panel, 30-50mm for desktop, 6-12mm for panel, and 10-15mm for drawer side plate and drawer back plate. In order to minimize the shrinkage and warpage of panel, the width of solid wood narrow board shall be limited. In modern furniture production, the general solid wood narrow board shall not exceed 60mm.
采用拼板结构,除了限制实木窄板的宽度外,同一拼板部件中的树种应一致或材性相近,相邻的实木窄板的含水率偏差不应大于1%。实木拼板的结构形式多种多样,因此实际生产中应根据不同用途选择合适的拼板形式。
济南酒店餐饮家具
The panel structure is adopted. In addition to limiting the width of solid wood narrow boards, the tree species in the same panel component shall be consistent or similar in wood properties, and the moisture content deviation of adjacent solid wood narrow boards shall not be greater than 1%. The structural forms of solid wood panels are diverse, so the appropriate panel forms should be selected according to different uses in actual production.
拼板简易步骤:
Simple steps for panel assembly:
1、选料:选料关系到后期板材的完美性,首先要尽量规避一些木料的缺陷地方,例如节疤、裂纹、凹口等。
1. Material selection: material selection is related to the perfection of later plates. First, try to avoid some defects of wood, such as knots, cracks, notches, etc.
2、材料准备:木工台锯切割出毛料(注意必须要比所拼料的实际尺寸大2-3cm,留出余量);通过平刨、压刨等,处理出材料的厚度。注意:处理时要留出余量,例如要实际拼厚度为25mm的板,此处可处理成27-28mm的板厚。
2. Material preparation: the woodworking bench saw shall cut the raw material (note that it must be 2-3cm larger than the actual size of the assembled material, with allowance); The thickness of the material is processed through flat planing, pressure planing, etc. Note: allowance shall be reserved during treatment. For example, the plate with the actual thickness of 25mm shall be spliced, which can be treated as the plate thickness of 27-28mm.
3、组坯:组坯对于成品家具质量的影响非常大,不合理的组坯,可能会使成品家具发生严重变形,甚至断裂等一系列问题。
3. Blank assembly: blank assembly has a great impact on the quality of finished furniture. Unreasonable blank assembly may cause serious deformation and even fracture of finished furniture.
4、涂胶。
4. Glue.
5、夹紧干燥。
5. Clamp dry.
我们一直在坚持分享的路上济南酒店餐饮家具https://www.jnzxjjpf.com真正为您解决您所需要的问题.
We have been insisting on sharing the dining furniture of Jinan hotel https://www.jnzxjjpf.com Truly solve the problems you need
相关产品
相关新闻
推荐产品
联系我们
/Contact us
济南众鑫家居
济南众鑫家居

15269186692

服务电话:15269186692

联系人:刘总

公司网址:https://www.jnzxjjpf.com/

联系地址:圣金元钢材超市(济南市天桥区G308)

联系人:刘总 手机:15269186692
地址:圣金元钢材超市(济南市天桥区G308)
备案号:鲁ICP备2021029317号
技术支持:网站建设·推广运营 网站地图    TXT    XML