1、 Repair paint finish

如果我们办公家具的漆面被烫坏了，我们可以用牙签上包一层细纹硬布，轻轻擦拭痕迹，然后涂上一层薄蜡，去除焦痕；如果家具的漆面擦伤，我们可以用与家具颜色一致的蜡笔或颜料，在家具的创面涂抹，给家具的表面上一层底色，然后用透明的指甲油薄薄的涂上一层防护；

If the paint surface of our office furniture is burned, we can wrap a layer of fine grained hard cloth with a toothpick, gently wipe the traces, and then apply a layer of thin wax to remove the scorch marks; If the furniture surface is scratches, we can use the crayons or pigments that are consistent with the furniture color, smear on the wound surface of the furniture, give the furniture a layer of background color on the surface, then use a transparent nail polish to smear a layer of protection.

二、办公桌面鼓泡

2、 Office desktop bubbling

如果我们的办公室桌椅表面鼓泡，可先用锋利刀片沿鼓泡中间顺木纹方向切开一刀，然后用注射器将胶水注入刀缝中，再用手指轻压泡泡上部，将溢出的胶水用湿布擦净，最后用一个底面光滑且大于鼓泡面积的重物压在上面。这样，鼓泡的装饰贴面就平整了。

If there are bubbles on the surface of our office tables and chairs, first cut a knife along the wood grain direction in the middle of the bubble with a sharp blade, then inject the glue into the knife seam with a syringe, then gently press the upper part of the bubble with your fingers, wipe the overflowing glue with a wet cloth, and finally press a weight with a smooth bottom and larger than the bubble area on it. In this way, the bubbling decorative veneer is flat.

三、修补凹痕

3、 Repair dents

一些家具因为木质比较软，碰撞后会留下凹痕，那么我们就要用湿毛巾先敷在凹陷处，再用熨斗加热熨平，即可复原，若是凹陷较深，我们可以添加填料。

Some furniture will leave dents after collision because the wood is relatively soft, so we need to apply a wet towel to the depression first, and then heat and iron it with an iron to restore it. If the depression is deep, we can add filler.

四、修补裂缝

4、 Repair cracks

如因热退缩产生裂痕，可采取以下补救措施：将旧棉布或破麻袋烧成灰状，再用桐油拌匀成糊状，嵌于木器上的缝隙中，阴干后再补平粘牢。或是把报纸撕得粉碎。加入一些明矾和清水，煮至粘稠，冷却后涂抹在木器的缝隙里，干燥后也很牢固。

In case of cracks due to thermal shrinkage, the following remedial measures can be taken: burn the old cotton cloth or broken gunny bag into ash, mix it with tung oil into a paste, embed it in the gap on the wood, dry it in the shade, and then make it flat and stick it firmly. Or tear the newspaper to pieces. Add some alum and clear water, cook until sticky, cool and apply it to the gap of wood. It is also very firm after drying.

五、去锈斑

5、 Remove rust spots

办公桌椅除锈镀铬家具生锈的话切记千万不可以用砂纸打磨，小型镀件可放入盛机油的盆中，浸泡八到十个小时，再用布擦拭。而大面积的镀件家具会生锈，可以先用刷子或棉纱蘸机油涂抹在锈斑上，稍候片刻，再用布擦拭，即可清除锈斑。

Rust removal of office desks and chairs. If chrome plated furniture is rusty, remember not to polish it with sandpaper. Small plated parts can be put into a basin containing engine oil, soaked for 8 to 10 hours, and then wiped with a cloth. Large areas of plated furniture will rust. You can first smear the rust spots with a brush or cotton yarn dipped in engine oil, wait a moment, and then wipe with a cloth to remove the rust spots.

今天的分享就是关于济南沙发卡座定做，更多的内容小编会不断的再此分享，更多的内容请继续关注我们：https://www.jnzxjjpf.com

Today's sharing is about the customization of Jinan sofa card seat. More content will be shared here. Please continue to pay attention to us: https://www.jnzxjjpf.com